Event message Short description Long description Detailed description
INS-BAT-400 Time not correct Time is not correctly set, or battery is low
INS-CLS-110 Envelope stoppage Transport failure between envelope closing and envelope exit
INS-CLS-111 Envelope stoppage Paperset too late at closer
INS-CLS-120 Document transport failure Document transport failure
INS-CLS-121 Envelope stoppage Envelope too late at stacker sensor
INS-CLS-290 Envelope stoppage Envelope closing sensor covered too long
INS-CLS-291 Envelope stoppage Closer sensor covered
INS-COM-900 Communication failure Internal communication failed
INS-COM-901 Communication failure Error in communication with FeederTower
INS-COM-902 Communication failure Error in communication with FeederTower
INS-COM-903 Communication failure Error in communication with FeederTower
INS-COM-904 Communication failure Error in communication with FeederTower
INS-COM-905 Communication failure Error in communication with FeederTower
INS-COM-906 Communication failure Error in communication with FeederTower
INS-COM-907 Communication failure Error in communication with FeederTower
INS-COM-908 Internal error Counters do not match
INS-COM-909 Communication failure with franking machine An internal time out error occurred which blocks job execution
INS-COM-910 Closed loop communication failure During job execution communication was lost
INS-COM-920 No communication with franking machine Franking machine required but not detected
INS-COM-921 Communication failure with franking machine The franking machine cannot handle a specific command.
INS-COM-922 Communication failure with franking machine Due to some fatal error communication has dropped with the franking machine
INS-COM-923 Communication failure with franking machine Due to some fatal error communication has dropped with the franking machine
INS-COM-924 Communication failure with franking machine Due to some fatal error communication has dropped with the franking machine
INS-COM-930 Closed loop communication failure Error in communication between inserter, MPPC camera and/or BSPI PC
INS-DC1-403 Technical failure DFC defective
INS-EH1-000 Empty envelope feeder Envelope feeder appears to be empty. If this is not the case, check the envelopes in the feeder, feeder width adjustment and envelope separation adjustment
INS-EH1-001 Empty envelope feeder The feeder does not contain envelopes
INS-EH1-111 Envelope stoppage Envelope stoppage
INS-EH1-200 Envelope too short Envelope length measured is shorter than expected
INS-EH1-201 Envelope too long Envelope length measured is longer than expected
INS-EH1-290 Unexpected envelope Envelope track sensor covered
INS-EH1-301 Envelope stoppage Skewed envelope
INS-EH1-302 Envelope stoppage Envelope stoppage
INS-EH1-303 Envelope separation failure Could not feed an envelope from the envelope feeder although it is not empty
INS-EH1-400 Technical failure Envelope feeder power on failure
INS-EOP-290 Unexpected envelope Envelope flap sensor covered
INS-EOP-300 Envelope not open Envelope flap not opened
INS-EOP-301 Envelope not open Envelope flap not opened
INS-EX1-100 Envelope stoppage Envelope blocked at side exit
INS-EX1-110 Envelope stoppage Envelope exit transport failure
INS-EX1-111 Document transport failure Document transport failure
INS-EX1-112 Envelope stoppage Too many envelopes at side exit
INS-EX1-290 Unexpected envelope Side exit sensor covered
INS-EX1-291 Envelope stoppage Unexpected document at side exit
INS-EX1-900 Conflicting settings Invalid exit settings received from system control
INS-GPR-300 GPRS error GPRS network signal cannot be detected
INS-GPR-301 GPRS error GPRS device could not complete network registration
INS-GPR-400 GPRS error Unable to read SIM card
INS-IDT-400 Technical failure ID tag write failure
INS-IDT-401 Option memory failure Identification and/or options memory could not be read, check options in the settings menu
INS-IDT-580 Technical failure ID tag missing
INS-INF-000 Auto clean on franking machine in progress System will restart automatically
INS-INF-001 Franking machine not ready for franking interface The franking machine is not ready as result of a condition before the inserter was started.
INS-INF-002 Auto clean on franking machine is finished Auto clean on franking machine is finished
INS-INF-003 Sealing on advanced feeder of franking machine is selected Preferably set sealing on inserter
INS-INF-100 Envelope stoppage between inserter and franking machine An envelope that has left the inserter system has not been franked in time.
INS-INF-200 Franking machine already started. Inserter can not control franking machine as it was already started via its start/stop key
INS-INF-201 Franking machine stopped via start/stop key Franking machine start/stop key pressed during run. Check stamps on last envelope(s)
INS-INF-202 User PIN code required at franking machine System will restart automatically after entering correct PIN code
INS-INF-203 Department PIN code required at franking machine Franking interface software does not support this feature
INS-INF-204 Wrong PIN code entered on franking machine The franking machine will go into sleep mode
INS-INF-205 User action required at franking machine User action required at franking machine
INS-INF-206 The franking machine is in supervisor mode The franking machine is in supervisor mode
INS-INF-207 ZIP zone required at franking machine Job execution is blocked until ZIP zone is entered
INS-INF-208 Franking machine job selected includes correction mode Franking interface software does not support this feature
INS-INF-209 Franking machine stopped via escape key The job is aborted because 'Escape' is pressed at franking machine
INS-INF-210 Franking machine is in stand alone mode Franking machine is in stand alone mode
INS-INF-211 Cover open on franking machine Franking machine cover opened during run
INS-INF-300 Communication failure with franking machine The franking machine did not recover from sleep mode in time
INS-INF-301 Communication failure with franking machine An internal time out error occurred which blocks job execution
INS-INF-302 An internal error occurred which blocks job execution The franking interface software is unable to stop the franking machine
INS-INF-303 Communication failure with franking machine The franking machine did not complete the starting sequence in time
INS-INF-304 The franking machine is in error mode The franking machine is in error mode
INS-INF-305 An internal error occurred which blocks job execution The franking machine is busy and won't accept commands from franking interface software
INS-INF-306 Auto clean on franking machine time out The auto clean cycle takes longer than expected.
INS-INF-307 No active rate table Probably Base only machine
INS-INF-308 Internal error on franking machine An unknown error occurred at the franking machine.
INS-INF-309 Manual clean of cartridge on franking machine failed Try again.
INS-INF-310 More envelopes have been franked than sent by the inserter system Possible presence of envelopes in franking machine from previous job or envelopes manually franked during the job
INS-INF-311 Selecting franking machine job failed Selecting franking machine job failed.
INS-INF-312 Selecting franking machine job failed Selecting franking machine job failed. The job does no longer exist.
INS-INF-313 Wait position occupied Franking interface software received data of next envelope too early
INS-INF-314 Franking machine job selected includes Dynamic batch mode Franking interface software does not support this feature
INS-INF-315 Weight exceeds limit No additional information
INS-INF-316 Envelope measures Invalid envelope measure for PPC management
INS-INF-317 An internal error occurred which blocks job execution Attempt to set an invalid franking mode
INS-INF-318 Sealing on advanced feeder of franking machine is selected It is not allowed to use sealing on both systems. Job setting of franking machine is overruled by inserter.
INS-INF-319 The franking value exceeded the 'High value threshold' Check document weight settings
INS-INF-900 Internal error on franking machine See franking machine for error details
INS-INF-901 Error or warning on franking machine See franking machine display for error details
INS-INF-902 Communication failure with franking machine Unknown or invalid envelope data received by franking interface software
INS-INF-903 Communication failure with franking machine Thickness information cannot be communicated with franking machine
INS-INF-904 An internal error occurred which blocks job execution Setting stamp configuration of franking machine failed
INS-INF-905 An internal error occurred which blocks job execution Getting system configuration of franking machine failed
INS-INF-906 An internal error occurred which blocks job execution Setting up the base of the franking machine failed
INS-INF-907 An internal error occurred which blocks job execution Setting up the advanced feeder of the franking machine failed
INS-INF-908 Internal failure on franking machine Setting up the dynamic scale of the franking machine failed.
INS-INF-909 Communication failure with franking machine The franking machine did not complete the stop sequence in time
INS-INF-910 Internal failure on franking machine Unexpected end meter action on franking machine
INS-INF-911 Communication failure Envelope data lost between inserter and franking interface software
INS-INF-912 Unknown envelope detected Envelope detected without data
INS-INF-913 Unknown envelope detected Envelope detected without a notification
INS-INF-914 An internal error occurred which blocks job execution The franking interface is busy and won't accept commands
INS-INF-915 FIFO Overflow FIFO Overflow for PPC variable mode
INS-INF-916 Rate calculation Rate calculation failure
INS-INF-917 An internal error occurred which blocks job execution Attempt to set an invalid franking interface software level
INS-INS-100 Document transport failure Document arrived too late at insert position
INS-INS-110 Document inserting failure Document inserting sensor is covered too long
INS-INS-111 Document transport failure Document transport failure
INS-INS-120 Document transport failure Document transport failure
INS-INS-200 Envelope stoppage Too many envelopes
INS-INS-290 Unexpected envelope Insert sensor covered
INS-INS-291 Unexpected document Unexpected document at document insert position
INS-INS-292 Envelope stoppage Insert table sensor covered
INS-INS-293 Envelope stoppage Unexpected envelope at insert table
INS-INS-300 Document set too thin Document set thickness measured too thin. Too few or wrong documents
INS-INS-301 Document set too thick Document set thickness measured too thick. Too many or wrong documents
INS-INS-303 Document length failure Inserted document length differs too much
INS-INS-400 Technical failure Insert track power on failure
INS-INS-500 Thickness not measured Wrong thickness measurement area
INS-JOB-000 No documents selected No documents selected
INS-JOB-001 Job cannot be run Job incompatible with system
INS-JOB-203 Job not possible BRE folded
INS-JOB-300 Job not possible Automatic fold setting not possible
INS-JOB-301 Internal error Exit not possible
INS-JOB-303 Job not possible Folded set too large
INS-JOB-304 Job not possible Folded set too small
INS-JOB-305 Job not possible Too many documents
INS-JOB-306 Job not possible Folded document does not fit in envelope
INS-JOB-307 Job not possible Measured length differs from length stated in job
INS-JOB-308 Job not possible Incorrect fold settings
INS-JOB-309 Job not possible Incorrect fold settings
INS-JOB-310 Job not possible Incorrect fold lengths for this foldtype
INS-JOB-311 Job not possible Address part too short
INS-JOB-312 Job not possible Address part too long
INS-JOB-313 Job not possible Middle part too short
INS-JOB-314 Job not possible Middle part too long
INS-JOB-315 Job not possible Rest part too short
INS-JOB-316 Job not possible Rest part too long
INS-JOB-317 Job not possible Address part or middle part too short
INS-JOB-318 Job not possible Address part or middle part too long
INS-JOB-319 Job not possible Middle part or rest part too short
INS-JOB-320 Job not possible Middle part or rest part too long
INS-JOB-321 Job not possible Address part or rest part too short
INS-JOB-322 Job not possible Address part or rest part too long
INS-JOB-323 Job not possible Document too long for system
INS-JOB-324 Job not possible Document too short for system
INS-JOB-325 Job not possible Envelope too long for system
INS-JOB-326 Job not possible Envelope too short for system
INS-LD1-200 Sealing fluid low Refill reservoir
INS-LD1-400 Sealing reservoir is missing Re-insert reservoir
INS-LIC-200 Invalid license key entered The entered license key is invalid for this system
INS-LIC-300 License missing License not available for requested action
INS-LIC-400 Update options failed Failed to write new options to option memory
INS-LIC-403 Invalid data in option memory/ID tag Option data invalid or not initialised
INS-M01-400 Technical failure Main motor failure
INS-MOD-201 No phone line detected No phone line detected by the modem
INS-MOD-300 Connection problem: no dial tone Technical failure
INS-MOD-301 Connection problem Technical failure
INS-MOD-302 Line busy Line busy
INS-MOD-303 No carrier No carrier
INS-MOD-304 Unexpected event detected Technical failure
INS-MOD-305 Unexpected event detected Technical failure
INS-MOD-306 Unexpected event detected Technical failure
INS-MOD-307 Unexpected event detected Technical failure
INS-MOD-308 Unexpected event detected Line in use
INS-MOD-309 Connection problem Technical failure
INS-MOD-310 Unexpected event detected Technical failure
INS-MOD-311 Unexpected event detected Technical failure
INS-MOD-312 Unexpected event detected Technical failure
INS-MOD-313 Unexpected event detected Technical failure
INS-MOD-314 Connection problem Technical failure
INS-MOD-315 Unexpected event detected Technical failure
INS-MOD-316 Connection problem Connection lost with server
INS-MOD-317 Unexpected event detected Technical failure
INS-MOD-318 Unexpected event detected Technical failure
INS-MOD-319 Unexpected event detected Technical failure
INS-MOD-320 Connection problem Connection problem
INS-MOD-321 Connection problem Connection problem
INS-MOD-322 Unexpected event detected Technical failure
INS-MOD-323 Unexpected event detected Technical failure
INS-MOD-324 Connection problem Modem not found
INS-MOD-325 Connection problem Modem not found
INS-MOD-326 Connection problem Technical failure
INS-MOD-327 Connection problem Connection problem
INS-MOD-328 Unexpected event detected Technical failure
INS-MOD-329 Unexpected event detected Technical failure
INS-MOD-330 Connection error Technical failure
INS-MOD-331 Connection problem Technical failure
INS-MOD-332 Unexpected event detected Technical failure
INS-MOD-333 Unexpected event detected Technical failure
INS-MOD-334 Unexpected event detected Technical failure
INS-MOD-335 Unexpected event detected Technical failure
INS-MOD-336 Unexpected event detected Technical failure
INS-MOD-337 Unexpected event detected Technical failure
INS-MOD-338 Unexpected event detected Technical failure
INS-MOD-339 Unexpected event detected Technical failure
INS-MOD-340 Connection problem Technical failure
INS-MOD-341 Unexpected event detected Technical failure
INS-MOD-342 Unexpected event detected Technical failure
INS-MOD-343 Unexpected event detected Technical failure
INS-MOD-344 Unexpected event detected Technical failure
INS-MOD-345 Unexpected event detected Technical failure
INS-MOD-346 Unexpected event detected Technical failure
INS-MOD-347 Unexpected event detected Technical failure
INS-MOD-348 Unexpected event detected Technical failure
INS-MOD-349 Unexpected event detected Technical failure
INS-MOD-400 Technical failure Initialisation of modem failed
INS-MOD-402 Modem failure Modem failure
INS-MOD-580 No modem detected No modem detected, no OLS possible
INS-MOD-581 Unexpected event detected Technical failure
INS-MOD-900 Unexpected event detected Technical failure
INS-MPC-301 No ID Scanner did not read an ID
INS-MPC-302 Invalid ID The ID of the last envelope is unknown
INS-MPC-303 Duplicate ID The ID of the last envelope was already processed before by BSPI
INS-MPC-304 ID's out of sequence The ID of the last envelope is out of sequence with the previous ones
INS-MPC-900 PC saving problem BSPI cannot sava the ID of the last envelope in its database
INS-MPC-901 PC problem The BSPI application encounters a problem
INS-OLS-000 Messages waiting New Online services messages are available
INS-OLS-001 Technical failure Communication board not configured for this system
INS-OLS-002 Technical failure Communication board not detected, no external communication possible
INS-OLS-003 Technical failure Communication failure between inserter and communication board
INS-OLS-004 Technical failure No modem detected, no OLS possible
INS-OLS-005 Technical failure Unknown modem type detected
INS-OLS-006 Technical failure Initialisation RS232 port failed, no franking connection possible
INS-OLS-007 Technical failure Initialisation modem failed
INS-OLS-008 Technical failure Clock update failed
INS-OLS-009 Technical failure Battery on communication board low
INS-OLS-010 Automatic connection failed Statistic buffer overflow >95%, batch data might be lost
INS-OLS-011 Technical failure Memory not available
INS-OLS-012 Technical failure Initialising memory
INS-OLS-013 Technical failure Initialising memory
INS-OLS-014 Technical failure Initialising memory
INS-OLS-015 Technical failure Unsupported software version detected
INS-OLS-016 Technical failure Flash memory communication board failure
INS-OLS-017 Technical failure Communication lost between inserter and connection board.
INS-OLS-018 Technical failure Communication lost between inserter and connection board.
INS-OLS-019 Technical failure Connection board restarted
INS-OLS-313 Unexpected event detected Technical failure
INS-OLS-314 Connection problem One or more steps of the connection failed
INS-OLS-315 Unexpected event detected Technical failure
INS-OLS-316 Disconnected unexpectedly The connection with Online services has ended unexpectedly
INS-OLS-317 Connection problem Can not connect to Online services
INS-OLS-318 Unexpected event detected Technical failure
INS-OLS-319 Connection failed Connection failed
INS-OLS-320 Connection problem Can not connect to Online services: protocol error
INS-OLS-321 Unexpected event detected Technical failure
INS-OLS-322 Unexpected event detected Technical failure
INS-OLS-323 Connection problem Can not connect to the host name of the OLS server
INS-OLS-324 Connection problem Can not connect to Online services
INS-OLS-325 Unexpected event detected Technical failure
INS-OLS-326 Connection problem The connection with Online services has ended unexpectedly
INS-OLS-327 Connection problem One or more steps of the connection failed
INS-OLS-328 Connection problem LAN adapter not configured correctly
INS-OLS-329 Connection problem Connection problem detected
INS-OLS-330 Unexpected event detected Undefined error reported by the communication stack
INS-OLS-331 Update failed Software updated cancelled by server
INS-P01-000 Envelope feeder sensor almost dusty Dusty envelope feeder sensor
INS-P01-300 Envelope feeder sensor dusty Dusty envelope feeder sensor
INS-P01-302 Technical failure Envelope feeder sensor defect
INS-P01-401 Technical failure Envelope feeder sensor defect
INS-P01-402 Technical failure Envelope feeder sensor defect
INS-P02-000 Envelope track sensor almost dusty Envelope track sensor error
INS-P02-300 Envelope track sensor dusty Envelope track sensor error
INS-P02-302 Technical failure Envelope flap sensor defective
INS-P02-401 Technical failure Envelope flap sensor defective
INS-P02-402 Technical failure Envelope track sensor defective
INS-P03-000 Envelope flap sensor almost dusty Envelope flap sensor error
INS-P03-300 Envelope flap sensor dusty Envelope flap sensor error
INS-P03-302 Technical failure Insert sensor defective
INS-P03-401 Technical failure Insert sensor defective
INS-P03-402 Technical failure Envelope flap sensor defective
INS-P04-000 Insert sensor almost dusty Insert sensor error
INS-P04-300 Insert sensor dusty Insert sensor error
INS-P04-302 Technical failure Exit sensor defective
INS-P04-401 Technical failure Exit sensor defective
INS-P04-402 Technical failure Insert sensor defective
INS-P05-000 Closer sensor almost dusty Dusty closer sensor
INS-P05-300 Closer sensor dusty Dusty closer sensor
INS-P05-302 Technical failure Closer sensor defect
INS-P05-401 Technical failure Closer sensor defect
INS-P05-402 Technical failure Closer sensor defect
INS-P06-000 Stacker sensor almost dusty Dusty stacker sensor
INS-P06-300 Stacker sensor dusty Dusty stacker sensor
INS-P06-302 Technical failure Stacker sensor defect
INS-P06-401 Technical failure Stacker sensor defect
INS-P06-402 Technical failure Stacker sensor defect
INS-P07-000 Exit sensor almost dusty Dusty exit sensor
INS-P07-300 Exit sensor dusty Dusty exit sensor
INS-P07-302 Technical failure Envelope track sensor defective
INS-P07-401 Technical failure Envelope track sensor defective
INS-P07-402 Technical failure Exit sensor defective
INS-P08-000 Skew sensor almost dusty Skew sensor error
INS-P08-300 Skew sensor dusty Skew sensor error
INS-P08-302 Technical failure Skew sensor defect
INS-P08-401 Technical failure Skew sensor defect
INS-P08-402 Technical failure Skew sensor defect
INS-P09-000 Insert table sensor almost dusty Dusty insert table sensor
INS-P09-300 Insert table sensor dusty Dusty insert table sensor
INS-P09-302 Technical failure Insert table sensor defect
INS-P09-401 Technical failure Insert table sensor defect
INS-P09-402 Technical failure Insert table sensor defect
INS-PB2-300 Memory failure FRAM chip contains old data. FRAM must be formatted, which will erase the contents. Photocells will be calibrated after formatting
INS-PB2-301 Memory failure FRAM chip contains corrupt data. FRAM must be formatted, which will erase the contents. Photocells will be calibrated after formatting
INS-PB2-402 Memory failure FRAM chip is not formatted. FRAM must be formatted. Photocells will be calibrated after formatting
INS-PB2-403 Memory failure FRAM could not be formatted
INS-PRC-001 Cover open Cover open
INS-PRC-002 Possibly wrong envelopes in system The job has been changed or a new job has been selected. There may be wrong envelopes in the system
INS-PRC-003 Stopcounter value reached Stop at count reached. Remove envelopes from exit. Press 'Start' to start a new cycle
INS-PRC-290 Unexpected documents in system Documents in system due to unexpected stop
INS-PRC-291 Stop mark read System stopped due to read stop command
INS-PRC-292 Divert mark read System stopped due to read divert command
INS-PRC-293 Documents in system Documents may still be in the system due to previous configuration, calibration or test
INS-PRC-300 Envelope stoppage Too many envelopes
INS-PRC-302 Internal error No paper set id
INS-PRC-303 Internal error Wrong paper set id
INS-PRC-304 Set diverted Set diverted due to internal failure
INS-PRC-305 Set too thick Folded set is too thick due to the number of sheets
INS-RE1-002 Mail set diverted Present on Deck & Stop mark read
INS-RE1-318 Internal error Missing OMR info for set
INS-SM1-900 Internal error Internal error in embedded machine control
INS-SM1-901 Internal error Internal error in embedded machine control
INS-SM1-902 Internal error Internal error in embedded machine control
INS-SM1-950 Internal error Internal error in embedded machine control
INS-SM1-951 Internal error Internal error in embedded machine control
INS-SM1-952 Internal error Internal error in embedded machine control
INS-SM1-953 Internal error Internal error in embedded machine control
INS-SM1-954 Internal error Internal error in embedded machine control
INS-SM1-955 Internal error Internal error in embedded machine control
INS-SM1-960 Internal error Internal error in embedded machine control
INS-SM1-961 Internal error Internal error in embedded machine control
INS-SM1-962 Internal error Internal error in embedded machine control
INS-SM1-963 Internal error Internal error in embedded machine control
INS-SM1-970 Internal error Internal error in embedded machine control
INS-SM1-971 Internal error Internal error in embedded machine control
INS-SM1-972 Internal error Internal error in embedded machine control
INS-SM1-973 Internal error Internal error in embedded machine control
INS-SM1-980 Internal error Internal error in embedded machine control
INS-SM1-999 Internal error Internal error in embedded machine control
INS-STK-000 Stacker almost full Remove envelopes from stacker
INS-STK-001 Stacker full Remove envelopes from stacker
INS-STK-110 Document transport failure Document transport failure
INS-STK-301 Envelope stoppage Envelope too early at stacker
INS-STK-401 Internal error Envelope stacker power on failure
INS-SW1-000 Cover open Cover open at start
INS-SW1-200 Cover open Cover open during run
INS-SW2-000 Cover open Cover open at start
INS-SW2-200 Cover open Cover open during run
INS-SW3-000 Cover open Cover open at start
INS-SW3-200 Cover open Cover open during run
INS-SW7-000 Cover open Cover open at start
INS-SW7-200 Cover open Cover open during run
INS-SYS-000 Preventive Maintenance needed Due to the number of inserts preventive maintenance is required
INS-SYS-002 Configuration changed Hardware configuration changed
INS-SYS-200 Serial number already present in ID tag Serial number was set before, and cannot be changed anymore
INS-SYS-301 Internal error Bootup problem
INS-SYS-302 Internal error Internal error, watchdog timeout
INS-SYS-304 Internal error Section timeout on control board
INS-SYS-306 Data has been reset A reset data has been performed
INS-SYS-400 Technical failure System Control PCB or ID tag defect
INS-SYS-500 Technical failure Timeout on configuration retrieval from real-time control board
INS-SYS-501 Technical failure Serial number in ID tag does not match serial number in FRAM
INS-SYS-502 Technical failure PCB and ID tag do not match machinetype
INS-SYS-503 Technical failure Pulses per mm ratio is not calibrated
INS-SYS-560 Incompatible software Software images in the system are incompatible
INS-SYS-561 Incompatible software Software images embedded control are incompatible
INS-SYS-580 Technical failure Real-time control board not found
INS-SYS-581 No VersaFeeder present According to the configuration settings a VersaFeeder is expected, but it cannot be detected
INS-SYS-900 Technical failure Internal error
INS-SYS-901 Internal error System state error
INS-SYS-902 Internal error System state error
INS-SYS-903 Internal error Unknown state message from feedersystem
INS-SYS-904 Internal error Illegal photocell id
INS-SYS-905 Internal error Illegal clutch id
INS-SYS-906 Internal error Illegal solenoid id
INS-SYS-907 Internal error Illegal digital sensor id
INS-SYS-908 Internal error Illegal machine state id
INS-SYS-909 Internal error System software error
INS-SYS-910 Internal error Paper transport could not be started
INS-SYS-911 Internal error Internal error, watchdog timeout
INS-SYS-914 Internal error System software error
INS-SYS-915 Internal error System software error
INS-SYS-916 Internal error System software error
INS-SYS-950 Internal error Internal error
INS-SYS-951 Internal error Timeout on sensor value retrieval
INS-SYS-952 Internal error Timeout on test ready
INS-SYS-999 Internal error System software error
INS-TR1-280 Envelope stoppage Envelope stoppage
INS-TR1-290 Unexpected envelope Envelope track sensor covered
INS-TR1-400 Internal error Envelope track power on failure
INS-TR2-400 Internal error Document track power on failure
INS-TR4-110 Envelope stoppage Stacker sensor covered too long
INS-TR4-290 Unexpected envelope Stacker sensor covered
INS-TR4-400 Internal error Document exit track power on failure
FT1-COM-900 Communication failure Error in communication with reading module/capture board
FT1-COM-901 Communication failure Error in communication with reading module/capture board
FT1-CS1-203 CIS sensor calibration error Paperwidth is too small to use for calibration
FT1-CS1-301 Calibration failure Calibration of the CIS failed
FT1-CS1-401 Technical failure CIS sensor is not calibrated properly
FT1-CS1-900 Technical failure General CIS reading error
FT1-CT1-100 Document transport failure Document stoppage at collator entry
FT1-CT1-120 Document transport failure Collator run out failure
FT1-CT1-270 Collator stopper position error Documents arrive too late at folder entry
FT1-CT1-271 Check document stopper position Based on the current job the document stoppers may have to be placed at another position to achieve the optimal performance
FT1-CT1-272 Check document stopper position Based on the current job the document stoppers may have to be placed at another position to achieve the optimal performance
FT1-CT1-273 Check document stopper position Based on the current job the document stoppers may have to be placed at another position to achieve the optimal performance
FT1-CT1-274 Check document stopper position The document stoppers must be placed at another position to run the job
FT1-CT1-275 Check document stopper position The document stoppers must be placed at another position to run the job
FT1-CT1-276 Check document stopper position The document stoppers must be placed at another position to run the job
FT1-CT1-290 Unexpected documents in system Stoppage at collator
FT1-DC1-380 DFC failure Document thickness cannot be measured
FT1-DC1-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC1-401 Technical failure DFC defective
FT1-DC2-380 DFC failure Document thickness cannot be measured
FT1-DC2-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC2-401 Technical failure DFC defective
FT1-DC3-380 DFC failure Document thickness cannot be measured
FT1-DC3-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC3-401 Technical failure DFC defective
FT1-DC4-380 DFC failure Document thickness cannot be measured
FT1-DC4-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC4-401 Technical failure DFC defective
FT1-DC5-380 DFC failure Document thickness cannot be measured
FT1-DC5-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC5-401 Technical failure DFC defective
FT1-DC6-380 DFC failure Document thickness cannot be measured
FT1-DC6-400 Technical failure Sensor cannot be adjusted correctly
FT1-DC6-401 Technical failure DFC defective
FT1-DF1-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF1-001 Empty feeder The feeder does not contain material
FT1-DF1-110 Document transport failure Feeder sensor is covered too long
FT1-DF1-200 Document too short Document length measured is shorter than expected
FT1-DF1-201 Document too long Document length measured is longer than expected
FT1-DF1-204 Incomplete set Empty feeder
FT1-DF1-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF1-301 Document too thick Document thickness measured too thick
FT1-DF1-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF1-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DF2-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF2-001 Empty feeder The feeder does not contain material
FT1-DF2-110 Document transport failure Feeder sensor is covered too long
FT1-DF2-200 Document too short Document length measured is shorter than expected
FT1-DF2-201 Document too long Document length measured is longer than expected
FT1-DF2-204 Incomplete set Empty feeder
FT1-DF2-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF2-301 Document too thick Document thickness measured too thick
FT1-DF2-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF2-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DF3-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF3-001 Empty feeder The feeder does not contain material
FT1-DF3-110 Document transport failure Feeder sensor is covered too long
FT1-DF3-200 Document too short Document length measured is shorter than expected
FT1-DF3-201 Document too long Document length measured is longer than expected
FT1-DF3-204 Incomplete set Empty feeder
FT1-DF3-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF3-301 Document too thick Document thickness measured too thick
FT1-DF3-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF3-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DF4-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF4-001 Empty feeder The feeder does not contain material
FT1-DF4-110 Document transport failure Feeder sensor is covered too long
FT1-DF4-200 Document too short Document length measured is shorter than expected
FT1-DF4-201 Document too long Document length measured is longer than expected
FT1-DF4-204 Incomplete set Empty feeder
FT1-DF4-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF4-301 Document too thick Document thickness measured too thick
FT1-DF4-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF4-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DF5-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF5-001 Empty feeder The feeder does not contain material
FT1-DF5-110 Document transport failure Feeder sensor is covered too long
FT1-DF5-200 Document too short Document length measured is shorter than expected
FT1-DF5-201 Document too long Document length measured is longer than expected
FT1-DF5-204 Incomplete set Empty feeder
FT1-DF5-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF5-301 Document too thick Document thickness measured too thick
FT1-DF5-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF5-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DF6-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
FT1-DF6-001 Empty feeder The feeder does not contain material
FT1-DF6-110 Document transport failure Feeder sensor is covered too long
FT1-DF6-200 Document too short Document length measured is shorter than expected
FT1-DF6-201 Document too long Document length measured is longer than expected
FT1-DF6-204 Incomplete set Empty feeder
FT1-DF6-290 Unexpected document in feeder Document present inside feeder while feeder tray is empty
FT1-DF6-301 Document too thick Document thickness measured too thick
FT1-DF6-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
FT1-DF6-305 Document separation failure Could not feed a document although the feeder is not empty
FT1-DG1-200 Technical failure Flex Dongle not correct
FT1-DV1-110 Document transport failure Stoppage at divert
FT1-FOL-100 Folder entry blockage Folder entry sensor covered too long
FT1-FOL-110 Document transport failure Stoppage at folder
FT1-FOL-111 Stoppage at folder First fold failure
FT1-FOL-112 Stoppage at folder Second fold failure
FT1-FOL-113 Stoppage at folder Third fold failure
FT1-FOL-290 Unexpected document Stoppage at folder
FT1-FOL-291 Stoppage at folder Document transport failure
FT1-FOL-900 Conflicting settings Invalid fold settings received from system control
FT1-JOB-000 Empty feeders No new documents found
FT1-JOB-306 Automatic job setup not possible Automatic fold could not be calculated
FT1-M01-400 Technical failure Collator motor failure
FT1-M02-400 Technical failure Divert motor failure
FT1-P01-300 Vertical track sensor dusty Vertical track sensor error
FT1-P01-301 Vertical track sensor error Vertical track sensor error
FT1-P01-302 Technical failure Vertical track sensor error
FT1-P01-303 Technical failure Vertical track sensor defect
FT1-P01-401 Technical failure Vertical track sensor defect
FT1-P01-402 Technical failure Vertical track sensor adjust error
FT1-P02-300 Collator sensor dusty Collator sensor error
FT1-P02-301 Collator sensor dusty Collator sensor error
FT1-P02-302 Technical failure Collator sensor error
FT1-P02-303 Technical failure Collator sensor defect
FT1-P02-401 Technical failure Collator sensor defect
FT1-P02-402 Technical failure Collator entry sensor adjust error
FT1-P03-300 Folder-in sensor dusty Folder-in sensor error
FT1-P03-301 Folder-in sensor dusty Folder-in sensor error
FT1-P03-302 Technical failure Folder-in sensor error
FT1-P03-303 Technical failure Sensor folder-in defect
FT1-P03-401 Technical failure Sensor folder-in defect
FT1-P03-402 Technical failure Sensor folder-in defect
FT1-P04-300 Folder-out sensor dusty Folder-out sensor error
FT1-P04-301 Folder-out sensor dusty Folder-out sensor error
FT1-P04-302 Technical failure Folder-out sensor error
FT1-P04-303 Technical failure Sensor folder-out defect
FT1-P04-401 Technical failure Sensor folder-out defect
FT1-P04-402 Technical failure Sensor folder-out defect
FT1-P05-300 Feeder sensor dusty Feeder sensor error
FT1-P05-301 Feeder sensor dusty Feeder sensor error
FT1-P05-302 Technical failure Feeder sensor error
FT1-P05-303 Technical failure Feeder sensor defect
FT1-P05-401 Technical failure Feeder sensor defect
FT1-P05-402 Technical failure Feeder sensor defect
FT1-P06-300 Feeder sensor dusty Feeder sensor error
FT1-P06-301 Feeder sensor dusty Feeder sensor error
FT1-P06-302 Technical failure Feeder sensor error
FT1-P06-303 Technical failure Feeder sensor defect
FT1-P06-401 Technical failure Feeder sensor defect
FT1-P06-402 Technical failure Feeder sensor defect
FT1-P07-300 Feeder sensor dusty Feeder sensor error
FT1-P07-301 Feeder sensor dusty Feeder sensor error
FT1-P07-302 Technical failure Feeder sensor error
FT1-P07-303 Technical failure Feeder sensor defect
FT1-P07-401 Technical failure Feeder sensor defect
FT1-P07-402 Technical failure Feeder sensor defect
FT1-P08-300 Feeder sensor dusty Feeder sensor error
FT1-P08-301 Feeder sensor dusty Feeder sensor error
FT1-P08-302 Technical failure Feeder sensor error
FT1-P08-303 Technical failure Feeder sensor defect
FT1-P08-401 Technical failure Feeder sensor defect
FT1-P08-402 Technical failure Feeder sensor defect
FT1-P09-300 Feeder sensor dusty Feeder sensor error
FT1-P09-301 Feeder sensor dusty Feeder sensor error
FT1-P09-302 Technical failure Feeder sensor error
FT1-P09-303 Technical failure Feeder sensor defect
FT1-P09-401 Technical failure Feeder sensor defect
FT1-P09-402 Technical failure Feeder sensor defect
FT1-P10-300 Feeder sensor dusty Feeder sensor error
FT1-P10-301 Feeder sensor dusty Feeder sensor error
FT1-P10-302 Technical failure Feeder sensor error
FT1-P10-303 Technical failure Feeder sensor defect
FT1-P10-401 Technical failure Feeder sensor defect
FT1-P10-402 Technical failure Feeder sensor defect
FT1-PB1-402 Technical failure Error during formatting FRAM memory
FT1-PB1-403 Technical failure Error during formatting FRAM memory
FT1-PB3-560 Technical failure Update of Reading firmware failed
FT1-PD1-400 Technical failure Main motor failure: pulse disc detects no or too few pulses
FT1-PRC-290 Unexpected documents in system Unexpected documents in system after job change
FT1-RE1-000 Set diverted Divert & Stop mark read
FT1-RE1-003 Final set part Part of previous set
FT1-RE1-300 Wrong reading window position End of reading window position exceeds document length
FT1-RE1-302 Reading error Not enough marks read
FT1-RE1-303 Reading error Conflicting basic commands read
FT1-RE1-304 Reading error No basic command read
FT1-RE1-305 Reading error Matching error
FT1-RE1-306 Reading error Document sequence error
FT1-RE1-307 Reading error Group sequence error
FT1-RE1-308 Reading error Wrong parity in code
FT1-RE1-309 Reading error Mark found at a position where no mark is supposed to be present
FT1-RE1-310 Reading error Incorrect mark distance
FT1-RE1-311 Reading error Too many marks read
FT1-RE1-312 Too many sheets in set Set size exceeded. If desired adjust the maximum number of sheets in the main document
FT1-RE1-313 Reading error No safety mark read
FT1-RE1-316 Reading error Unexpected accumulate mark read
FT1-RE1-319 Mail set could not be finished Stop has been pressed. System cannot run empty with reverse reading
FT1-RE1-321 Reading error The barcode could not be read correctly. Document not correctly loaded or barcode position not correctly configured.
FT1-RE1-322 Reading error Barcode too long
FT1-RE1-323 Reading error Barcode too short
FT1-RE1-324 Reading error The set does not start with page 1
FT1-RE1-326 Reading error The number of pages in a set (M) cannot be 0
FT1-RE1-327 Reading error The number of pages in the set (M) changed before the set was complete
FT1-RE1-332 Reading error Set sequence error
FT1-RE1-343 Wrong configuration sheet A wrong configuration sheet is read
FT1-RE1-344 Reading error The configuration sheet contains a function that is not supported with the current license
FT1-RE1-345 Reading error The page number could not be read correctly
FT1-RE1-346 Reading error The page number could not be interpreted correctly
FT1-RE1-380 Reading test failure Reading test failed
FT1-SW2-000 Cover open Cover open at start
FT1-SYS-381 Check daily mail switch position For the current job the daily mail switch must be positioned in the manual feed position
FT1-SYS-382 Check daily mail switch position For the current job the daily mail switch must be positioned in the auto position
FT1-SYS-580 Configuration changed FT3 and TO missing
FT1-SYS-581 Technical failure Feeder block 1-2 failure
FT1-SYS-582 Technical failure Feeder block 3-4 failure
FT1-SYS-583 Technical failure Feeder block 5-6 failure
FT1-SYS-584 Technical failure Feeder block 3-6 failure
FT1-SYS-585 Technical failure No divert found
FT1-SYS-586 Technical failure Configuration error, reading board expected!
FT1-SYS-900 Configuration failure Configuration changed: daily mail missing
FT1-SYS-901 Configuration failure Configuration changed: daily mail missing
FT1-SYS-902 Configuration failure Configuration changed: daily mail missing
FT1-SYS-903 Configuration failure Configuration changed: daily mail missing
FT1-SYS-904 Configuration failure Configuration changed: daily mail missing
FT1-SYS-905 Configuration failure Configuration changed: daily mail missing
FT1-TR1-110 Document transport failure Document stoppage at vertical track
VF1-COM-900 Communication failure Error in communication with VersaFeeder
VF1-DC1-380 DFC failure Document thickness cannot be measured
VF1-DC1-401 Technical failure DFC defective
VF1-DF1-000 Empty feeder Feeder appears to be empty. If this is not the case, check the documents in the feeder and the feeder adjustments
VF1-DF1-001 Empty feeder The feeder does not contain material
VF1-DF1-110 Document transport failure Feeder sensor is covered too long
VF1-DF1-201 Feeding failure Document length error
VF1-DF1-202 VersaFeeder separation open The separation release handle of the VersaFeeder is in the open (up) position
VF1-DF1-301 Document too thick Document too thick
VF1-DF1-302 Feeding failure Wrong thickness reference: last document measured is too thin. The previous document may be a double!
VF1-DF1-305 Document separation failure Could not feed a document although the VersaFeeder is not empty
VF1-JOB-000 Empty feeders No new documents found
VF1-M01-400 VersaFeeder motor failure VersaFeeder motor failure. Check if the power of the VersaFeeder is switched on. If this is the case, please note the error code and call service
VF1-P01-000 Feeder sensor almost dusty Feeder sensor dusty
VF1-P01-300 Feeder sensor dusty Feeder sensor dusty or defect
VF1-P01-401 Technical failure VF feeder sensor adjust error
VF1-P02-000 Transport input sensor almost dusty Transport input sensor dusty
VF1-P02-300 Transport input sensor dusty Transport input sensor dusty or defect
VF1-P02-401 Technical failure VF transport input sensor adjust error
VF1-P03-000 Transport output sensor almost dusty Transport output sensor dusty
VF1-P03-300 Transport output sensor dusty Transport output sensor dusty or defect
VF1-P03-401 Technical failure VF transport output sensor adjust error
VF1-PB1-405 Technical failure Memory failure
VF1-PD1-400 Technical failure Main motor failure: pulse disc detects no or too few pulses
VF1-PRC-290 Learn cycle not possible Document too far in feeder to learn automatic job
VF1-SW1-200 Cover open Cover open during run
VF1-SYS-580 Technical failure Incorrect configuration
VF1-TR1-100 Document transport failure Document stoppage at feeder input
VF1-TR1-101 Document transport failure Documents do not arrive at feeder
VF1-TR1-110 Document transport failure Documents do not arrive at feeder exit
VF1-TR1-111 Document too long Document too long
VF1-TR1-120 Document transport failure Documents do not leave feeder exit
VF1-TR1-290 Unexpected document Transport track sensor covered
VF1-TR1-291 Unexpected document Transport track sensor covered
Date created:
12/17/2013 16:06:00
Last updated:
12/17/2013 16:27:19
Product(range):
DS-90i
Print